Cable exhaust control KDS 110 DIBt
Item no.: 300740The magnetic switch of the KDS 110 set with DIBt approval monitors the window position and transmits the information via a thin cable to a built-in control unit with a potential-free 5 A change-over relay. In this way, an exhaust air system can only be operated with a tilted or open window if it is ensured that sufficient fresh air flows into the room and thus no negative pressure is created that could draw dangerous and toxic carbon monoxide from a combustion site. Depending on the connection option (e.g. Miele PUR 98), the light of the bonnet can also be switched on independently of the window position.
GAS ALARM GX-CO-12
Item no.: 300712
Areas of application
- mobile use in camping vehicles and on ships
- Camper, caravan
- other recreational vehicles with gas cooking and cooling facilities
- boiler room with gas heating or boiler
Mounting bracket f. mini float switch
Item no.: 300787
GAS ALARM GX-B2pro
Item no.: 300926
The socket gas warning device with external sensor for town gas and natural gas is plugged into a socket and the sensor is set to an upper (natural gas / methane) or lower (liquid gas / butane, propane) position depending on the gas. The warning device is ready for operation after 3 minutes of preheating time and warns already far below dangerous gas concentrations with a loud alarm tone and red flashing LED.
Possible applications
- Monitoring of gas heating or gas cooker / detection of town, natural and liquid gases
- Monitoring of the heating and utility rooms
- Storage of liquid gas cylinders or camping gas
- Air conditioners / coolants
CO ALARM GX-C3pro
Item no.: 300229
The socket CO warning device with external sensor for carbon monoxide is plugged into a socket and the sensor is placed at average nose level. The warning device is ready for operation after 5 minutes and warns with the alarm thresholds specified in DIN standard 50291 with an alarm tone and a red flashing LED. In the event of an alarm, the device connected to the GX-C3pro, e.g. a gas heater, is also reliably switched off, whereby the device remains switched off until the user has ensured that his ventilation measures have had an effect and he resets the device by briefly unplugging it and plugging it back into the socket.
Possible applications
- Monitoring in case of leakage of carbon monoxide from all heat generating equipment in apartments, houses, stores, ...
- Monitoring of all gas-operated systems and safety shutdown in the event of elevated CO levels
- for gas heaters, gas heating, gas cookers, gas furnaces, oil heating and any combustion facility with supply
- Can also be used in the bathroom and other damp rooms as long as moisture does not condense
- Designed for years of continuous operation
Water detector SHT 5001
Item no.: 400748
The SHT 5001 water detector for top-hat rail mounting in the fuse box or small distribution board has 2 independent detection lines, which are designed identically with the option of connecting sensors or mini float switches to their own inputs in each case, activating the alarm memory via wire jumper or switching a potential-free changeover relay when "water" is detected. Test, reset, internal alarm beeper, or the connection of external alarm indicators with 12 volts to 30 mA, on the other hand, are carried out together for both detection lines. The cable lengths can be extended for sensors up to 100 meters, for mini-float switches up to 300 meters per signal line, provided that only thin and unshielded 2x0.14mm² LiYY cables are used, which are not laid parallel to lines of the mains AC voltage.
GX-D11
Item no.: 400311
The plug-in CO2 traffic light with internal NDIR sensor, the LED displays red, yellow and green, as well as discreet acoustic support, is used in areas where a reminder for regular ventilation is necessary, but people present should not be unsettled by yellow and red warning colours that are visible from afar.
GAS ALARM GX-D33
Item no.: 300257- CO2 warning device for tea kitchens
- according to DIN6653-2
The GX-D33 with internal sensor for carbon dioxide from pressurized CO2 bottles is plugged into one of the lower sockets located near the CO2 bottles to be monitored, is ready for operation after 3 minutes of preheating time and warns when 3.0%vol. CO2 is reached with a loud alarm sound and red flashing LED. It is the easiest to use CO2 detector for water bubblers with large CO2 bottles in small rooms.
Flue gas temperature monitor ATW 519 - KDS 110/116
Item no.: 201753The Cetrotec flue gas temperature monitor type 519 with 40°C switching point and 10-k resistor is approved for use in heat generating plants and is mounted with a flange on a free piece of furnace pipe with a minimum diameter of 120 mm. Its normally open contact is only intended for control tasks and has been bridged by us with a 10 kOhm cable breakage protection resistor, therefore this version of the temperature monitor is only suitable as an optional accessory for our KDS cable exhaust air controls in order to enable an exhaust air system when the stove is cold without having to open a window each time as well, provided that the approval of the master chimney sweep is available, since an exhaust air control in combination with an exhaust gas temperature monitor does not have DIBt approval.
Water detector SHT 227 Pump control
Item no.: 300227
The water detector for pump control!
The SHT 227 socket water detector functions as a pump control. If a certain water level is detected with the mini float switch, the socket switches on the connected pump and an alarm sounds. After the water level drops below the specified level, the pump continues to run for an adjustable follow-up time of 0 to 100 seconds, is then switched off and the alarm stops again.
Possible applications
- Water ingress
- Pump sump
- Cistern monitoring
- Also suitable for other liquids (e.g. heating oil, diesel, vegetable oil, lubricating oils, etc.)
GAS ALARM GX-A1+
Item no.: 300892
The universal gas warning device for surface-mounted fixed installation is suitable for different gases depending on the sensor. It provides the operating voltage required for the sensor, regulates the heating current required for some sensors and evaluates the sensor voltage returned by the sensor and displays it on its illuminated plain text display. Based on the different voltages, the GX-A1+ recognizes five different states, including the pre-alarm from 2.0 volts and the main alarm from 2.5 volts, at which not only the potential-free changeover relay assigned to the alarm switches, but the entire warning device makes itself clearly audiovisually noticeable with a loud alarm tone and flashing display lighting. There are sensors for city and natural gas, refrigerant (HFC) and carbon dioxide in two measuring ranges; for carbon monoxide a separate set GX-A1+CO is available, as the TÜV-tested CO sensors are addressed and evaluated differently.
Possible applications
- Detection of town, natural and liquid gases
- Methane, butane, propane, ethanol
- Gastronomy, CO2 bottles, dispensing systems
- Dry ice processing and storage
- Detection of refrigerants such as R-32, R-404a, R-410a, etc.
Aquastop SHT 216
Item no.: 300260
Water detector SHT 240
Item no.: 300240
Prof. CO2 warning device for carbon dioxide GX-D500
Item no.: 300267
Possible applications
- for dispensing systems with carbon dioxide (CO2 carbon dioxide)
- according to DIN 6653-2
- Small to medium-sized breweries, wine and fermentation cellars
- Gastronomy with beverage dispensing equipment
- Dry ice storage and processing
- all plants with CO2 from pressure cylinders
WWD 150 Wireless Water Detector float switch
Item no.: 200150
PROF. CO ALARM GX-C330
Item no.: 300330
The CO ALARM GX-C330 is a carbon monoxide warning device for monitoring indoor areas with open combustion and is equipped with an integrated electro-chemical sensor. An LCD display constantly informs about the operating status as well as the exact measured ppm number of the CO concentration in the ambient air.Possible applications
Possible applications
- Shisha bars and smoking clubs
- Monitoring the proper functioning of ventilation systems
- Laboratory environments in universities, schools and companies
- Occupational safety measures for open burns in the catering industry
- Storage of CO in pressure cylinders
Ball protection grid for CO2 traffic light
Item no.: 300947
Water sensor SHT 5009 for floor mounting
Item no.: 300720
Accessories for water detector
The water sensor SHT 5009 with three plate electrodes is suitable for floor mounting on soft floors such as parquet, laminate, but also carpets or linoleum floors. With its 2-wire cable it is directly ready for connection to the Schabus water detectors SHT 5000 and SHT 5001, as well as to the level controller SHT 5002 as overflow detector. The middle drill hole is reinforced with aluminum, so depending on the type of mounting desired, a thread can also be cut.
PROF. CO ALARM GX-C300P
Item no.: 300256Professional carbon monoxide warning device for permanent installation with warning levels and alarm delay times as specified in the DIN EN 50291 standard and suction device by means of a silicone hose to monitor thermally demanding rooms (e.g. gas-operated sauna). Display of the exact measured CO concentrations in ppm on an illuminated plain text display. In the event of an alarm and technical faults detected by the unit itself, a potential-free changeover relay switches in each case, e.g. to activate forced ventilation or to inform the BMS. The internal electrochemical sensor has a service life of 6 to 10 years, depending on the ambient conditions, and can easily be replaced by Elektrotechnik Schabus at the factory.
GAS ALARM GX-D2
Item no.: 300252The plug-in CO2 warning device with external sensor for carbon dioxide is simply plugged into a socket and the sensor is placed in an upper (more tolerant) or lower (more sensitive) position depending on the desired sensitivity. It is ready for operation after 3 minutes of preheating time and warns when half the MAC (2500 ppm) is reached with a loud alarm tone and red flashing LED.
CO GAS ALARM GX-C1pro
Item no.: 300783
The socket carbon monoxide warning device with internal electrochemical CO sensor is plugged into a medium-sized socket, is ready for operation after 5 minutes initialisation time and warns of excessive CO concentrations strictly according to the specifications of DIN EN 50291 for carbon monoxide in living spaces with a loud alarm tone and red flashing LED. The sensor, the evaluation, the measuring cell with its calibration as well as the software developed by Elektrotechnik Schabus were subjected to a full test at TÜV Süd according to DIN EN 50291, safety and stability were certified for the system.
Possible applications
- Monitoring for carbon monoxide leakage at combustion sites in flats, houses, shops, small businesses, cafés, low-dust workshops
- Monitoring of all gas-fired installations
- For gas heaters, gas heating, gas cookers, gas ovens, but also oil heaters and open fires, can also be used in bathrooms and other damp rooms, as long as moisture does not condense.
- Designed for years of continuous operation
Dirt trap accessories for mini float switches
Item no.: 300320
Aqua Scanner SHT 5020
Item no.: 300746
The Aqua Scanner SHT 5020 is a 2 meter long sensor (extendable on request), sensitive to single drops of water along its entire length. The mechanically strong cable, resistant to corrosion and abrasion, consists of two sensor wires embedded in a fluoropolymer carrier rod. Due to the robust cable construction with conductive polymer technology and fluoropolymer construction detection, no metal is exposed. For cleaning, you can wipe it with a clean damp cloth.
For connection to the Schabus water detectors is suitable only a LiYY control line with 2x 0.14mm², which can be ordered separately.
Possible applications
- Accessories for SCHABUS water detectors SHT 5000, 5001 and 5002
- 100% made in Germany
- for laying under kitchen and bathroom furniture
- under aquariums
- under other devices, where water can leak over a wide area
- under pipes, tubs, tanks ...
- for indoor projects such as data centers / control rooms / HVAC / IOT
Suspended float switch plastic
Item no.: 200950
Comfort package FTW 519 with FDS 100 set
Item no.: 300519
This comfort package without DIBt approval includes a classic FDS 100 exhaust air control set consisting of a radio window switch with intermediate plug receiver and an FTW exhaust gas temperature monitor with integrated transmitter for long, completely free (not jacketed) stove pipes at a minimum height of 80 cm (measured from the top of the stove). This means that for very infrequently used furnaces, a window does not always have to be opened every time the exhaust air system is used.
Hint: Involve your chimney sweep in your planning before ordering so that nothing stands in the way of acceptance afterwards. There are significant regional differences over which Elektrotechnik Schabus has no influence. 
Water detector SHT 5002
Item no.: 300749
The SHT 5002 water detector for top-hat rail mounting in the fuse box or small distribution board is designed as a level controller and has 2 different detection lines. Detection line 1 is the actual level controller, which receives the functions "Fill" or "Drain" by means of a wire jumper and switches its potential-free 5 A changeover relay depending on a lower and an upper level, each of which is defined by a mini float switch. Detection line 2 works like a simple water detector and is called "overflow detector" here, i.e. as soon as water is detected by a sensor or mini-float switch, the second relay of the SHT 5002 switches over.
Water detector SHT 218
Item no.: 300218
The SHT 218 socket water detector functions as a pump control. If soil moisture is detected with the sensor, the socket switches on the connected pump and the LED visually indicates the water ingress. After the sensor has dried, the pump continues to run for an adjustable follow-up time of 0 to 100 seconds and is then switched off.
Aquastop SHT 226
Item no.: 300228
The Aquastop SHT 226 is a protection system with device shutdown. The electronic alarm and shutdown device detects the smallest amounts of liquid and switches off the connected device.
Possible applications
- Detection of water level changes (at least 4 cm)
- also for other liquids (e.g. fuel oil, diesel, vegetable oil, lubricating oil, etc.)
Mini float switch plastic normally open contact
Item no.: 200940
Standard mini float switch made of plastic for our water detectors SHT 5000, SHT 5001 and SHT 5002 with reed contact (25 V AC / 60 V DC / max. 0.5 A / max. 10 W) for all types of water and liquid media from 0.7 g / cm³, encapsulated with 2.5 metre long LiYY cable.
Possible applications
- Accessories for SCHABUS water detectors SHT 5000 and 5001, 5002
Radio climate control FKS 100
Item no.: 301268
Do not cool and heat out the window!
The transmitter of the FKS 100 set monitors the window position and transmits the information by radio to a built-in receiver with potential-free 5 A changeover relay. In this way, an air conditioner can be switched off automatically when the window is tilted or open, so that the outside air is not cooled and energy is wasted unnecessarily.
Starting current limiter ASB 116 2500W/10A
Item no.: 300116
Gas sensor GX-SE City / natural gas
Item no.: 200897-SE
Gas sensor GX-CO
Item no.: 200898-CO
Radio exhaust air control FGS 170
Item no.: 300714
The FGS 170 radio gas heater control system consists of a 230-volt transmitter, which interrogates the potential-free contact of a gas heater, and a 230-volt receiver, which converts the change of state of the gas heater into a changeover of the potential-free changeover relay. With this system, a bathroom fan, for example, can be switched off when the gas heater is ignited.
Radio exhaust air control FDS 216
Item no.: 300460
The transmitter of the FDS 216 set without DIBt approval monitors the window position and transmits the information by radio to an intermediate plug receiver with a switched 16 A socket. In this way, an exhaust air system can only be operated with a tilted or open window if it is ensured that sufficient fresh air flows into the room and thus no negative pressure is created that could draw dangerous and toxic carbon monoxide from a combustion site.
Possible applications
- Fume cupboard control
- Exhaust air tumble dryer
- Simple receiver installation in seconds
Relay plug-in card accessories SHT 5000
Item no.: 300747
The optionally available relay plug-in card for the SHT 5000 assigns each of the 4 detection lines, in addition to the main relay, its own small changeover relay, which is polled by the WWD 200 smart home adapter. In contrast to the main relay, the 4 small relays of the relay plug-in card are not energized in monitoring mode and only pick up when the assigned detection line is activated by the water. The relay plug-in card has no influence on the various setting options of the SHT 5000 and can be retrofitted at any time.
CO detector 40 ppm
Item no.: 7639852
Water sensor SHT 5006
Item no.: 300745
Accessories for water detector
The standard SHT 5006 water sensor with 2 nickel-plated brass contacts and 6 meters of cable is overmolded with a soft, water-repellent plastic and has a gap between the contacts to prevent any biofilms that may form from triggering false alarms. The SHT 5006 sensor for connection to all Schabus water detectors is only suitable for regularly dry environments, ideal for detecting creeping moisture on floors and surfaces, but rather unsuitable for detecting water levels in shafts, tanks and other containers with regularly damp environments.
Comfort package FDS 100 / FTX 519
Item no.: 300539This comfort package without DIBt approval includes a classic radio exhaust control set FDS 100 consisting of a window switch with built-in receiver and a radio exhaust temperature monitor FTX with remote transmitter for shorter or covered, but always freely accessible stovepipes. This means that for very rarely used stoves, a window does not always have to be opened every time the exhaust air system is used.
Hint: Involve your chimney sweep in your planning before installation so that nothing stands in the way of acceptance afterwards. There are significant regional differences, on which Elektrotechnik Schabus has no influence.
Water detector SHT 228
Item no.: 300219
The water detector for pump control!
The SHT 228 socket water detector functions as a pump control. If a certain water level is detected with the mini float switch, the socket switches on the connected pump and in contrast to the SHT 227, the SHT 228 does not sound an alarm. After the water level drops below the specified level, the pump continues to run for an adjustable run-on time of 0 to 100 seconds and is then switched off.
Possible applications
- Water ingress
- Pump sump
- Cistern monitoring
- Also suitable for other liquids (e.g. heating oil, diesel, vegetable oil, lubricating oils, etc.)
Water detector SHT 5000 12-24V
Item no.: 300790
SHT 5000 - the all-rounder among the water detectors - now optimized for the WWD 200 smart home adapterwhich sends you push notifications to your smartphone via the Smart Live app.
Areas of application
- Water ingress / water pipe burst
- Pump control
- Cistern monitoring
- Level monitoring
- Overflow message (e.g. drainage shaft)
- Monitoring flat roofs
- Combined with mini float switch also suitable for other liquids (e.g. heating oil, diesel, vegetable oil, lubricating oils, etc.)
- Automatic bilge pumps (SHT5000-24 V for boats)
- for water sports, hobby brewers, aquariums, model making, swimming pools, bathrooms and kitchens, workshops, etc.
- IP 65 on request
Radio magnetic switch FDS 098 L
Item no.: 300198
Additional transmitter for a second window can be combined with the FDS 100, FDS 200 and FDS 216 devices. At least one window must be open for the exhaust air system to be switched on.
The serial number can be found on the type plate of the radio receiver or transmitter under the barcode field.
Longlife additional transmitter for FDS 100/200/216
FTW 519 Comfort package with FDS 200 set
Item no.: 300529
This comfort package without DIBt approval includes a classic FDS 200 exhaust air control set consisting of a radio window switch with built-in receiver and an FTW exhaust gas temperature monitor with integrated transmitter for long, completely free (unjacketed) stovepipes at a minimum height of 80 cm (measured from the top edge of the stove). This means that for very rarely used furnaces, a window does not always have to be opened as well every time the exhaust air system is used.
Hint: Involve your chimney sweep in your planning before ordering so that nothing stands in the way of acceptance afterwards. There are significant regional differences over which Elektrotechnik Schabus has no influence. 
Mini float switch V2A normally open contact
Item no.: 200941
Stainless steel mini float switch for our water detectors SHT 5000, SHT 5001 and SHT 5002 with reed contact (25 V AC / 60 V DC / max. 0.5 A / max. 10 W) for food, water and many other liquid media from 0.7 g / cm³, to which stainless steel is resistant. Encapsulated with a 2.5 metre long LiYY cable.
Cable magnetic switch KMS 098K22
Item no.: 300743
Additional magnetic switch for KDS 110/116/210 and KDT 210
The additional magnetic switch for a second (or more) window is equipped with 2 screw terminals and is mounted between the control unit and the original magnetic switch. The connection is made with a 2-wire LiYY control cable. The OR function is achieved, only one of the two windows must be open for an exhaust air control KDS / KDT to release the fan motor or an air conditioning control KKS to switch off the air conditioning.
Water detector SHT 217
Item no.: 300217
The SHT 217 socket water detector functions as a pump control. If the sensor detects soil moisture, the socket switches on the connected pump and an alarm sounds. After the sensor has dried, the pump continues to run for an adjustable follow-up time of 0 to 100 seconds, is then switched off and the alarm stops again.
Possible applications
- Water ingress
- Pump control
- Cistern monitoring
- Pump sump (dry)
Radio exhaust air control FDS 100 DIBt
Item no.: 300268
The transmitter of the FDS 100 set with DIBt approval monitors the window position and transmits the information by radio to a built-in receiver with a potential-free 5 A changeover relay. In this way, an exhaust air system can only be operated with a tilted or open window if it is ensured that sufficient fresh air flows into the room and thus no negative pressure is created that could draw dangerous and toxic carbon monoxide from a combustion site.
GAS ALARM GX-D3
Item no.: 300233
Gas sensor GX-H2
Item no.: 200616
CO2 traffic light "school
Item no.: 400250
The CO2 traffic light "school" with internal NDIR sensor is an indicator of the carbon dioxide content in the room air and provides a visual warning of increasingly poor air quality in indoor areas where many people frequently spend time and encourages regular draught ventilation.
The device is not approved for any other use than described above.
Water sensor SHT 5090
Item no.: 300721
CO2 traffic light OFFICE
Item no.: 400380
In the hectic office routine, it is often noticed too late - many different factors cause the proverbial "thick air".
Our oxygen supply continuously decreases and we become flabby and tired. Fresh air means more oxygen - thus more well-being and more performance.
The CO2 traffic light "office" helps you to ventilate in time, to ventilate for a sufficiently long time and thus to ventilate in a sensible energy-saving way. This way you feel fit again faster - and that is logically also healthier.
Possible applications
- Room air monitoring in the office according to EU standard EN 13779
- Individual office, reception offices, open plan office, meeting rooms and more.
- reliable reminder to ventilate regularly
BBB 300 Potential-free contact | Light control
Item no.: 200603
The BBB300 add-on module turns a switched socket (e.g. KDS 210 and FDS 200 exhaust air controls) into a potential-free contact that can be loaded with up to 5 amps. Ideal for using the control contacts of newer exhaust systems with existing socket exhaust control, but also to switch off only the motor and leave the lighting untouched. The switching behavior is: socket switched on = contact closed.
SHT 450 water detector with sensor cable
Item no.: 300450
No matter where ...
whether kitchen base cabinets, laundry rooms, bathroom furniture or the aquarium in the living room:
the SHT 450 detects water leaks everywhere with its sensor line and alerts you before worse damage occurs.
The 2 meter long sensor cable (extendable on request), reacts sensitively to single drops of water along its entire length. The mechanically strong cable, resistant to corrosion and abrasion, consists of two sensor wires embedded in a fluoropolymer carrier rod. Due to the robust cable construction with conductive polymer technology and fluoropolymer construction detection, no metal is exposed. For cleaning, you can wipe it with a clean damp cloth.
For connection to the Schabus water detectors is suitable only a LiYY control line with 2x 0.14mm², which can be ordered separately.
Possible applications
- Water ingress
- 100% made in Germany
- for laying under kitchen and bathroom furniture
- under aquariums
- under other devices, where water can leak over a wide area
- under pipes, tubs, tanks ...
- for indoor projects such as data centers / control rooms / HVAC / IOT
- Cistern monitoring
- Level monitoring
Radio exhaust air control FDS 200 DIBt
Item no.: 300462
Possible applications
The transmitter of the FDS 200 set with DIBt approval monitors the window position and transmits the information by radio to an intermediate plug receiver with a switched 5 A socket. In this way, an exhaust air system can only be operated with a tilted or open window if it is ensured that sufficient fresh air flows into the room and thus no negative pressure is created that could draw dangerous and toxic carbon monoxide from a combustion site.
Gas sensor GX-LNG
Item no.: 300897
Gas Alarm GX-HS
Item no.: 400200
WWD 100 Wireless Water Detector
Item no.: 200100
WWD 200 Smart Home Adapter
Item no.: 200200
Extension cable Schuko 3×2,5mm 30m
Item no.: 300230
Extension cable Schuko 3×2,5mm 20m
Item no.: 300220
Extension cable Schuko 3×2,5mm 10m
Item no.: 300210
Extension cable Schuko 3×1,5mm 50m
Item no.: 300150
Extension cable Schuko 3×1,5mm 40m
Item no.: 300140
Extension cable Schuko 3×1,5mm 30m
Item no.: 300130[vc_row][vc_column][vc_text_separator title=”Lieferprogramm Elektrotechnik SCHABUS” align=”align_left” color=”custom” accent_color=”#c20012″][/vc_column][/vc_row][vc_row][vc_column][vc_column_text]Elektrotechnik Schabus ist Entwickler und Hersteller der hochwertigen Warnsysteme und sicherheitstechnischen (Funk-) Lösungen. Diese Lösungen entwickeln wir durch unsere Nähe am Markt Geschehen und am Kunden. Nur so wissen wir, was die Endverbraucher suchen und brauchen. Zusätzlich entwickeln wir elektronische und elektromechanische Spezialanfertigungen für Unternehmen unterschiedlichster Branchen. Mit Elektrotechnik Schabus haben Sie einen erfahrenen Partner zur Seite, der Sie von der Entwicklung bis hin zur Fertigung und Montage bei Ihrem Projekt kompetent begleitet. Sie haben die Idee – wir setzen die Lösung um![/vc_column_text][/vc_column][/vc_row]